![midwayusa beretta d spring midwayusa beretta d spring](https://i.ytimg.com/vi/7RnH2CImo4s/maxresdefault.jpg)
Trigger pull with "Comp" spring DA= 8.0lbĮach pull weight was derived at by averaging 10 pulls for each stat. Installed Dave Olhasso's competition spring in all three and went to the range today Fri 7-28-06.ĩ2FS-Trigger pull factory spring = DA 11.8lbĩ6 Brig. The following is from a post on the Beretta Forum: (shows the results of different hammer springs) Wolff Springs sells a calibration pack that includes a 16,17,18, and 19# spring.
#Midwayusa beretta d spring series#
It came from a Colt 1911 MKIV Series 80 Combat Commander in stainless, and I am pretty sure that I saw some pix of other Colts with this same black plastic trigger.I believe the stock hammer spring is 20#. I got the pistol used from Bob's Little Sport shop last month, and he didn't have any history on it so I don't know the date of manufacture, etc. It's definitely plastic, and I have a hard time imagining that anyone would have opted for this voluntarily, but I did think that it was weird for Colt to cheap out on this. I'll checkout the websites mentioned above, but would appreciate any info you have on a gunsmith. Thanks, I am pretty new to all of this, and expected them to have at least similar trigger pulls. If you do need a good Beretta gunsmith I think I know one or two in the are that used to work on them, although they might be in PA now. Basically you are comparing an average at best trigger with some of the best. In fact, the trigger of a 1911 is what makes it the most favorite competition gun around, just because it is THAT good, and the Ruger is also a favorite of target shooters everywhere. Most traditional DA/SA guns like the Beretta will not have the smooth clean trigger pull of a 1911 or MKIII. Out of curiosity can you post a picture of the plastic Colt trigger? I have one of those but have never installed it. Beretta Italy sells it and you need to order it directly from their site.
#Midwayusa beretta d spring how to#
A easier way you can do if you don't know how to do the above yourself is to get a trigger with an overtravel screw installed. Some smith welds a stop somewhere to limit the travel. some material needs to be removed between the contact surface of the trigger bar and safety lever that pushes on the firing pin block plunger. This can be easily done on most hammer fired semi.
![midwayusa beretta d spring midwayusa beretta d spring](https://zahal.org/wp-content/uploads/2017/10/Beretta-98F-Recoil-Reduction-Spring-Rod-by-DPM-Systems.png)
If you are getting a trigger job done the smith usually knows how to reduce it. The single action travel(over travel) can be reduced. Cylinder and Slide makes a nice set with improved geometry.ģ. replace the plastic trigger with a metal one. this is the main spring used for the DAO 92fs and is lighter and will give you a ligher double action and single action pull. If you want to do it yourself here's some simple and effective things you can do: a. Send it to a gunsmith who specializes in the 92fs/m9 and have a trigger job done.Ģ. Here's my suggestion on how to improve it:ġ. The trigger itself is made out of plastic. Most DA/SA pistols can't compare to a single action gun. Yes, the 92FS trigger will feel nothing like a single action gun like 1911 or the Ruger MKIII. The Colt had a plastic trigger? I don't think they ever made a gun with a platic trigger. Is this normal for a Beretta 92fs? I'm not sure if we should keep looking for trigger upgrades, or if we should send back to Beretta, or if this is just normal for this gun. I tried looking on MidwayUSA to see if they sell the same type of trigger upgrades for the 92fs that they do for the 1911, but it doesn't seem to be the case. Even after you rack the slide, there is a lot of travel distance, and it feels spongy. Since then, and since shooting the Ruger, we've really noticed how sloppy the Beretta trigger feels in comparison.
![midwayusa beretta d spring midwayusa beretta d spring](https://i.ytimg.com/vi/ItIVFNj15mE/sddefault.jpg)
Once of the first things the hubby did was to replace the Colt plastic stock trigger with a Nighthawk aftermarket one, which made a world of difference in look and feel. Since then, we've also picked up a used Colt 1911 Series 80 Combat Commander and a new Ruger Mkiii Hunter (we both have our FID cards and 3 P2P each - if only the NJGF arms race allowed husband-wife teams!). It was purchased new in December, and we were really happy with it at first. My husband and I have recently gotten into target shooting, and the Beretta 92FS was our first semi auto pistol. Hi all, hope that you can recommend a fix.